Sticker Care Guide: Keep "Daisy" and "Sly No. 1" Looking Sharp

Start with what these stickers actually are

Both "Daisy" and "Sly No. 1" are durable vinyl stickers featuring original artwork by Holly Bones. Each measures approximately 3x4 inches and is suitable for indoor and outdoor use. The material is high-quality white vinyl with a satin finish and a 1/8" (3.2mm) white kiss-cut border around the sticker.

That construction matters for care: the vinyl is water, scratch, and UV resistant, and the adhesive is removable without residue. These traits give you room to clean and reposition, but they do not make the sticker indestructible. The practical goal is to protect the printed surface and the adhesive edge so the sticker stays flat and legible.

The two stickers in this guide

• "Sly No. 1" Sticker: "Sly No. 1" Sticker: approximately 3x4 inches, high-quality white vinyl with a satin finish, 1/8" (3.2mm) white kiss-cut border, water/scratch/UV resistant, removable adhesive without residue. These are the exact traits that determine how you clean it, where you can apply it, and how you handle the edge if it starts to lift.

  

• "Daisy" Sticker: "Daisy" Sticker: approximately 3x4 inches, high-quality white vinyl with a satin finish, 1/8" (3.2mm) white kiss-cut border, water/scratch/UV resistant, removable adhesive without residue. The care approach is the same as for "Sly No. 1," so you can use one routine for both stickers.

  

Choose a surface that lets the adhesive do its job

The kiss-cut border is your handling zone: it gives you a clean edge to press down without touching the printed art. Apply the sticker to a smooth, clean, dry surface. Dust, oil, or texture under the vinyl can create air pockets and give water a path under the edge.

Because the adhesive is removable without residue, you can lift and reposition the sticker if you misalign it. Do that gently and avoid repeated peeling, which can stretch the vinyl or weaken the adhesive over time. The supplied information does not specify a recommended temperature range or a maximum outdoor exposure period, so treat very hot, very cold, or heavily abraded surfaces as uncertain rather than guaranteed.

A simple cleaning routine that protects the print

The vinyl is water resistant, but the printed artwork and the adhesive edge still deserve gentle handling. Use the least aggressive method that removes the mark.

1. 1. Start dry: Wipe loose dust with a soft, dry cloth. This removes grit before it can scratch the satin finish.
2. 2. Use a damp cloth for light marks: Dampen a soft cloth with water and wipe gently. Avoid soaking the sticker or letting water pool along the kiss-cut border.
3. 3. Skip harsh cleaners: The supplied information does not confirm compatibility with solvents, abrasives, or alcohol-based cleaners. Stick to water and a soft cloth unless you have tested a small area.
4. 4. Dry the edge: After cleaning, pat the border dry so moisture does not sit under the vinyl and encourage lifting.

Sticker peeling edges fix: what to do when a corner lifts

A lifting edge is the most common sticker problem, and the fix depends on why it lifted. Work through these checks before pressing it back down.

• Clean and dry first: Lift the edge gently, remove any dust or grit underneath, and let the surface dry completely. Pressing dirt back under the sticker only creates a new failure point.
• Press from the center outward: Use your thumb or a soft cloth to push air toward the edge, then hold the border down for a few seconds. The kiss-cut border gives you a clean area to press without touching the artwork.
• Avoid heat as a shortcut: The supplied information does not confirm a safe temperature for heat-assisted application. Do not use a hair dryer or iron unless the manufacturer provides instructions.
• Know when to stop: If the adhesive has picked up debris or the vinyl has stretched, repeated pressing will not restore a flat edge. The removable adhesive lets you take the sticker off without residue, but the supplied information does not confirm that it can be reapplied indefinitely.

Sticker lifespan tips for indoor and outdoor use

The stickers are rated for indoor and outdoor use and are UV resistant, but lifespan still depends on placement. Direct, intense sun, repeated abrasion, and frequent wetting are harder on any vinyl sticker than a sheltered spot. Rotate the sticker's position if you notice fading or edge wear, and keep the surface free of grit.

One practical note: these stickers are made-to-order through a print-on-demand partner and shipped directly to you. They may differ slightly in appearance from stickers purchased at in-person events. That is a production difference, not a care issue, but it is worth knowing before you compare a new sticker with one you bought at a show.

What the supplied information does not cover

Good care advice includes knowing the limits of the evidence. The product records do not include preparation steps, a recommended application temperature, a maximum outdoor exposure time, or confirmed compatibility with specific cleaning products. If you need those details, ask before applying the sticker to a surface where failure would be costly, such as a vehicle finish or a textured outdoor fixture.

• No confirmed heat-setting instructions: Do not assume a hair dryer or heat gun is safe for the vinyl or the adhesive.
• No confirmed solvent list: Water and a soft cloth are the only cleaning method supported by the supplied facts.
• No confirmed reapplication limit: The adhesive is removable without residue, but the records do not state how many times a sticker can be repositioned.